PCS-100斷刀檢測器 PCS-100斷刀檢測器
PCS-100
斷刀檢測器
破損檢測器
破損檢測系統
深圳市漢斯福特科技有限公司
李工
：
: 3174269615
公司地址：龍華新區大浪街道大浪社區偉達工業園A棟2樓
公司：www.huntsort。。ｃｏｍ
- Uni-body Design for Ultimate Sealing
一體成型機身工藝，高密封設計
- Shaft-Direct Drive (Without Gear Box)
軸直接驅動式，不帶齒輪箱
- Set Bolt
固定螺栓
- Adjust Ring for Swing Angle
旋角調整環
- V Cup Seal
V型密封
- Needle Cap (To be mounted or removed by the set screw)
針帽，可通過固定螺絲進行裝卸
- Needle Length Std: 140mm Long Needle: 200mm Max.
探針長度，標準：140mm，zui大：200mm
- Flat Wand (Option) 110mm (L) 3mm (W)
防護桿（選裝），長110mm，寬3mm
- Carbide deposited
針表面超硬化處理
探針擺動 | 擺動角度5-175° |
電機驅動 | 直接驅動式直流電機 |
工作電壓 | 直流24V |
zui大電流 | 250mA |
運行溫度 | 0-55℃ |
1. Contact Sensor PCS-100 with Needle Assembly
接觸式傳感器/探頭PCS-100以及探針配套裝置
Contact sensor PCS-100
- Rotation angle can be set and/or changed flexibly CW or CCW, in the range of 5° to 175°.
可通過設置或者更改旋轉方向來調整旋轉角度，調整范圍為5°到175°.
Setting CW or CCW on the control unit depends on where the sensor/needle is set, and which one could achieve the nearest contact to the tool.
在控制器上操作，并據傳感器探針的位置和就近被測工具的原則來調整旋轉方向
- Contact pressure of needle (speed of needle swing) can be changed in 3 steps by the switch of control unit. The lowest swing speed is ideal for the small dia. of tools. Up to about 0.4mm dia. of tools can be detected.
只需要三步即可在控制器上調整探針的接觸壓力（探針旋轉速度），zui低旋轉速度適合測小尺寸的被測工具，zui小測量工具尺寸為0.4mm。
- Swing speed of the needle can be selected in several steps. It can help to minimize the cycle time of machining.
探針旋轉速度只需要遵循幾個步驟操作即可進行選擇，這樣能有效地縮短機器加工周期
2. Control Unit SCU-100
SCU-100控制單元
OK output
If a tool is detected, OK relay outputs a momentary or latch signal. Green LED illuminates.
當被測件被檢測到良好，繼電輸出一個瞬間信號，綠LED燈亮起。
FAULT output
When a broken tool condition is detected, FAULT relay outputs a momentary or latch signal Red LED illuminates.
當檢測到破損件時，瞬間發出一個故障信號，紅色LED燈亮起
System Fault
A system Fault signal outputs at Fault relay when
在以下情況會發出系統故障信號：
- The sensor malfunction.
傳感器故障
- The sensor direction setting and the CW/CCW switch setting are opposite.
傳感器方向設置和正反旋轉方向轉換設置錯反
- There is a short or disconnection at the sensor cable
傳感器電纜線短路后者斷開
Both Red and Green LED illuminate
此時紅綠燈同時亮起
3. Connecting Cable (STD: 5m) with L90 Connector
配有L90接頭的電纜線，標準長5m
4. Clamping Collar
夾圈
代理：深圳市漢斯福特科技有限公司
公司：www.huntsort。。ｃｏｍ
公司地址：龍華新區大浪街道大浪社區偉華達工業園A棟2樓
：
Housing 外殼 | Anodized Aluminum 陽極電鍍鋁 |
Needle swing 探針擺動 | Swing Angle 5-175°mechanically adjustable 擺動角度5-175°，機械可調 |
Needle 探針 | Max Life needle in standard length 140mm, Long needle 200 mm (Heat-Treated) 標準長140mm，zui長200mm（熱處理） |
Motor drive 電機驅動 | Direct Drive (No Gear Box) DC motor 直接驅動式直流電機，不帶齒輪箱 |
Sealing 密封 | Sealed against liquid and solid contaminants. Rating IP-67 高密封，防止液體和固體污染侵蝕，防護等級達IP67 |
Cable 電纜 | 90°or straight, moulded 4 pin connector. Standard length 5M (Max. 50M) 垂直或者水平電纜線，帶4針接頭，標準長5m，zui大長為50m |
| SCU-100 Control Unit SCU-100 控制單元 |
Operating voltage 工作電壓 | 24VDC 直流24V |
Max. current zui大電流 | 250mA |
Operating Temp. 運行溫度 | 0-55℃ |
Housing Material 外殼材質 | Polycarbonate 聚碳酸脂 |
Max. wire size zui大線規 | 12AWG |
Mounting 安裝方式 | 35mm DIN Rail 35mm導軌，符合德國工業標準 |
OK Fault relay 正常/故障信號繼電輸出 | Dry Contact (Contact Rating) 干接觸（接點容量） |
Additional Functions 附件功能 | Changeable to reverse logic for space monitoring 空間監測時，逆向理論信號切換 |
